cisco路由器子接口配置
@有哈3345:cisco 路由器 这样进入子接口配置模式?
杜风13582598899…… 进入配置模式命令:conf t 进入接口(以端口fa0/1为例):int fa0/1 线路配置: line console 0
@有哈3345:如何配置cisco路由器的串行接口 -
杜风13582598899…… Router(config)#int s1/0 //进入串口s1/0配置模式 Router(config-if)#ip address 192.168.1.1 255.255.255.0 //配置ip地址和子网掩码 Router(config-if)#clock rate 64000 //设置时钟频率为64KHz,DCE端必须配置,DTE端不需要配置 Router(config-if)#ba Router(config-if)#bandwidth 64 //设置带宽为64Kbps Router(config-if)#no shutdown //激活端口
@有哈3345:怎么在cisco 路由器上配置串行接口的子接口 -
杜风13582598899…… conf t int s0/0.1
@有哈3345:cisco路由器子接口配置是怎样做到的谁知道 -
杜风13582598899…… int f0/0 no shut int f0/0.1(和VLAN2通信) encap dot1q 2 ip add 192.168.2.254 255.255.255.0 no shut int f0/0.2(和VLAN3通信) encap dot1q 3 ip add 192.168.3.254 255.255.255.0 no shut
@有哈3345:思科路由器的虚拟子接口配置本征vlan怎么配 -
杜风13582598899…… 进入子接口.然后封装encapsulation的时候会encap dot1q vlanid +native.
@有哈3345:要在思科路由器上的以太口配置两个子接口,VLAN分别是1、2,如何配置? -
杜风13582598899…… int f0/0 //假设是这个以太网口配置子接口 int f0/0.1 //创建子接口,序号随意 encap dot1q 1 //封装的VLAN,这个不是随意的,VLAN是几号就是几号 ip address **** **** //配置地址 int f0/0.2 encap dot1q 2 ip address **** ****
@有哈3345:思科传统路由配置 -
杜风13582598899…… Router>en Router#conf t Router(config)#hostname R1 (路由器命名) R1(config)#interface fastethernet0/1 (进入内网口) R1(config-if)#ip address 192.168.1.1 255.255.255.0(配ip) R1(config-if)#no shut (端口激活) R1(config-if)#speed 10 (...
@有哈3345:Cisco 路由器基本设置过程步骤? -
杜风13582598899…… enable configure terminal no ip domain-lookup line console 0 logging synchronous exec-timeout 0 0 no login line aux 0 logging synchronous exec-timeout 0 0 no login privilege level 15 line vty 0 4 no login privilege level 15 exit no cdp run no ip http server基本信息.先配好...再配接口 链路测试(ping) 需要跑路由再配路由 ..这就是层次化配置 这样配置 容易排错.
@有哈3345:Cisco交换路由之间配置
杜风13582598899…… 在交换机上配一个子接口啊 router(config)#int f0/0.1 #ip add 192.168.1.2 255.255.255.0 #no shut
@有哈3345:如何配置CISCO路由器? -
杜风13582598899…… Cisco路由器配置中端口是非常重要的部分,同时我们也要考虑配置文件和进程,才能彻底做好路由器的配置工作.几乎所有路由器都在路由器背后安装了一个控制台端口.控制台端口提供了一个EIA/TIA—232(以前叫作RS—232)...
杜风13582598899…… 进入配置模式命令:conf t 进入接口(以端口fa0/1为例):int fa0/1 线路配置: line console 0
@有哈3345:如何配置cisco路由器的串行接口 -
杜风13582598899…… Router(config)#int s1/0 //进入串口s1/0配置模式 Router(config-if)#ip address 192.168.1.1 255.255.255.0 //配置ip地址和子网掩码 Router(config-if)#clock rate 64000 //设置时钟频率为64KHz,DCE端必须配置,DTE端不需要配置 Router(config-if)#ba Router(config-if)#bandwidth 64 //设置带宽为64Kbps Router(config-if)#no shutdown //激活端口
@有哈3345:怎么在cisco 路由器上配置串行接口的子接口 -
杜风13582598899…… conf t int s0/0.1
@有哈3345:cisco路由器子接口配置是怎样做到的谁知道 -
杜风13582598899…… int f0/0 no shut int f0/0.1(和VLAN2通信) encap dot1q 2 ip add 192.168.2.254 255.255.255.0 no shut int f0/0.2(和VLAN3通信) encap dot1q 3 ip add 192.168.3.254 255.255.255.0 no shut
@有哈3345:思科路由器的虚拟子接口配置本征vlan怎么配 -
杜风13582598899…… 进入子接口.然后封装encapsulation的时候会encap dot1q vlanid +native.
@有哈3345:要在思科路由器上的以太口配置两个子接口,VLAN分别是1、2,如何配置? -
杜风13582598899…… int f0/0 //假设是这个以太网口配置子接口 int f0/0.1 //创建子接口,序号随意 encap dot1q 1 //封装的VLAN,这个不是随意的,VLAN是几号就是几号 ip address **** **** //配置地址 int f0/0.2 encap dot1q 2 ip address **** ****
@有哈3345:思科传统路由配置 -
杜风13582598899…… Router>en Router#conf t Router(config)#hostname R1 (路由器命名) R1(config)#interface fastethernet0/1 (进入内网口) R1(config-if)#ip address 192.168.1.1 255.255.255.0(配ip) R1(config-if)#no shut (端口激活) R1(config-if)#speed 10 (...
@有哈3345:Cisco 路由器基本设置过程步骤? -
杜风13582598899…… enable configure terminal no ip domain-lookup line console 0 logging synchronous exec-timeout 0 0 no login line aux 0 logging synchronous exec-timeout 0 0 no login privilege level 15 line vty 0 4 no login privilege level 15 exit no cdp run no ip http server基本信息.先配好...再配接口 链路测试(ping) 需要跑路由再配路由 ..这就是层次化配置 这样配置 容易排错.
@有哈3345:Cisco交换路由之间配置
杜风13582598899…… 在交换机上配一个子接口啊 router(config)#int f0/0.1 #ip add 192.168.1.2 255.255.255.0 #no shut
@有哈3345:如何配置CISCO路由器? -
杜风13582598899…… Cisco路由器配置中端口是非常重要的部分,同时我们也要考虑配置文件和进程,才能彻底做好路由器的配置工作.几乎所有路由器都在路由器背后安装了一个控制台端口.控制台端口提供了一个EIA/TIA—232(以前叫作RS—232)...